Averick Apps › Ursa QC › Guides
AQL inspection for garments: sample sizes, the AQL chart and a calculator
How buyers and QC inspectors decide how many pieces to check, and when a lot passes or fails, explained for apparel with real numbers.
In short: for most garment final inspections, buyers use general inspection level II with zero critical defects, AQL 2.5 for major and AQL 4.0 for minor. Look up the lot size to get the sample size, inspect that many pieces, and compare the count of defective pieces with the accept and reject numbers.
What AQL means
AQL stands for Acceptable Quality Limit (often called Acceptable Quality Level). It comes from the sampling standard ISO 2859-1, which is equivalent to ANSI/ASQ Z1.4. Instead of checking every garment, the inspector checks a random sample. The AQL number sets how many defective pieces the sample can contain before the whole lot is rejected.
A lower AQL is stricter. AQL 1.5 allows fewer defective pieces than AQL 2.5, which allows fewer than AQL 4.0.
Critical, major and minor defects
Each defect found is classed by how serious it is, and each class has its own AQL:
- Critical (AQL 0): a safety or legal risk, such as a broken needle left in a garment, sharp hardware, or a drawstring on children's wear that breaks safety rules. One critical defect fails the lot.
- Major (usually AQL 2.5): affects fit, function or saleability, such as a measurement outside tolerance, an open seam, a broken zip, a shade difference or a missing label.
- Minor (usually AQL 4.0): cosmetic, unlikely to cause a return, such as a loose thread end or slightly uneven stitching.
Buyers often tighten these for children's wear or premium lines (for example major 1.5, minor 2.5). Your buyer's quality manual always overrides these defaults.
Inspection levels: why level II is the default
The inspection level sets how big the sample is for a given lot size:
- Level II is the default in ISO 2859-1 and the one used for most garment inspections.
- Level I uses a smaller sample, for suppliers with a strong track record.
- Level III uses a larger sample, for suppliers with recent problems or high-value goods.
- Special levels S-1 to S-4 use very small samples, for slow or destructive tests.
Quick AQL calculator
Enter the lot size and pick the AQL. This uses general inspection level II, single sampling, normal inspection.
Code letter K · lot of 1,201 to 3,200 pieces.
AQL chart for garments (general inspection level II)
Each cell shows the number of pieces to inspect, then accept / reject. Where the standard points to a neighbouring plan, the adjusted sample size is already filled in.
| Lot size | Code | AQL 1.5 | AQL 2.5 | AQL 4.0 |
|---|---|---|---|---|
| 2 – 8 | A | 8 · 0/1 | 5 · 0/1 | 3 · 0/1 |
| 9 – 15 | B | 8 · 0/1 | 5 · 0/1 | 3 · 0/1 |
| 16 – 25 | C | 8 · 0/1 | 5 · 0/1 | 3 · 0/1 |
| 26 – 50 | D | 8 · 0/1 | 5 · 0/1 | 3 · 0/1 |
| 51 – 90 | E | 8 · 0/1 | 5 · 0/1 | 13 · 1/2 |
| 91 – 150 | F | 8 · 0/1 | 20 · 1/2 | 20 · 2/3 |
| 151 – 280 | G | 32 · 1/2 | 32 · 2/3 | 32 · 3/4 |
| 281 – 500 | H | 50 · 2/3 | 50 · 3/4 | 50 · 5/6 |
| 501 – 1,200 | J | 80 · 3/4 | 80 · 5/6 | 80 · 7/8 |
| 1,201 – 3,200 | K | 125 · 5/6 | 125 · 7/8 | 125 · 10/11 |
| 3,201 – 10,000 | L | 200 · 7/8 | 200 · 10/11 | 200 · 14/15 |
| 10,001 – 35,000 | M | 315 · 10/11 | 315 · 14/15 | 315 · 21/22 |
| 35,001 – 150,000 | N | 500 · 14/15 | 500 · 21/22 | 315 · 21/22 |
| 150,001 – 500,000 | P | 800 · 21/22 | 500 · 21/22 | 315 · 21/22 |
| 500,001 + | Q | 800 · 21/22 | 500 · 21/22 | 315 · 21/22 |
Single sampling, normal inspection. If the sample size is equal to or larger than the lot, inspect every piece.
Worked example: a lot of 3,000 T-shirts
- Find the code letter. 3,000 pieces falls in 1,201 – 3,200, code letter K.
- Read the sample size. At level II, code K means inspecting 125 pieces, pulled at random from across cartons, sizes and colours.
- Read the limits. Major at AQL 2.5: accept up to 7, reject at 8. Minor at AQL 4.0: accept up to 10, reject at 11. Critical: any one fails the lot.
- Inspect and count defective pieces. Say you find 6 pieces with major defects and 9 with minor defects, and no critical.
- Decide. 6 is within 7 and 9 is within 10, so the lot passes. Had there been 8 major-defective pieces, it would fail even with zero minor defects.
Most buyers count defective pieces, not individual defects. A shirt with an open seam and two loose threads counts once, as a major. Confirm the counting rule with your buyer before you start.
Where measurements fit in
Measurement checks are part of the same inspection. Each point of measure (chest, body length, sleeve and so on) is checked against the tech pack spec and its tolerance. A measurement outside tolerance is normally logged as a major defect. Buyers usually set their own measurement sample per size and colour in their QC manual, separate from the visual sample.
This is the slowest part of an inspection on paper: hold the tape, read the number, put the tape down, write it, compare it to the spec, repeat for every point on every piece.
AQL sampling and measurements, without the clipboard
Ursa QC has AQL sampling built in: it works out the sample size and gives the accept or reject result. Inspectors speak each measurement hands-free and the app compares it against the tech pack spec, then produces the report as PDF or Word.
See Ursa QC Message us on WhatsAppFrequently asked questions
What does AQL 2.5 mean in garment inspection?
AQL 2.5 is the acceptable quality limit most buyers use for major defects. For a lot of 1,201 to 3,200 pieces at level II, you inspect 125 pieces; the lot passes with up to 7 defective pieces and fails at 8.
What AQL is used for critical, major and minor defects?
A common default is zero for critical, 2.5 for major and 4.0 for minor, at general inspection level II. Buyers often tighten this for children's wear or premium lines. Always follow the buyer's own quality manual.
Which inspection level should be used for garments?
General inspection level II, the default in ISO 2859-1. Level I uses smaller samples, level III larger ones, and S-1 to S-4 are for small samples such as slow or destructive tests.
Do I count defects or defective pieces?
Usually defective pieces. A garment with several defects counts once, under its most serious class. Confirm the method with your buyer before the inspection.
What if the sample size is larger than the lot?
Inspect every piece in the lot.